300-510 Questions Pass on Your First Attempt Dumps for CCNP Service Provider Certified
300-510 Practice Test Pdf Exam Material
Cisco 300-510 exam is a challenging exam that requires a thorough understanding of network technologies and protocols. 300-510 exam consists of 60-70 multiple-choice and scenario-based questions, and candidates are given 90 minutes to complete it. 300-510 exam is available in English and Japanese and can be taken at any Pearson VUE testing center worldwide.
NEW QUESTION # 96
Refer to the exhibit.
Refer to the exhibit. R21 is a multicast source sending multicast traffic 224.1.1.1 to R23, with RP22 serving as the rendezvous point inside AS65222. A network engineer noticed that when R21 goes down, R12 in AS65111 starts to send the same multicast group 224.1.1.1 through RP11. Which action resolves the issue ?
- A. Disable PIM parse mode between RP11 and RP22 in the two autonomous systems.
- B. Enable passive intertaoe under EIGRP between the two autonomous systems.
- C. Block service groups 224.0.1.39 and 224.0.1.40 between the two autonomous systems
- D. Advertise RP2 with a high local preference in AS65222.
Answer: C
NEW QUESTION # 97
Refer to the exhibit.
An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2. In order for all EIGRP routes to be redistributed correctly, which action should be taken?
- A. Router 1 must remove the AS number 1 from the redistribution command for all EIGRP routes to be redistributed.
- B. Router 1 must have the keyword ospf-metric included in the redistribution command for all EIGRP routes to be redistributed.
- C. Router 1 must have the keyword metric-type 1 included in the redistribution command for all EIGRP routes to be redistributed.
- D. Router 1 must have the keyword included in the redistribution command for all EIGRP routes to be redistributed.
Answer: D
NEW QUESTION # 98
An engineer is working to implement segment routing protocol on the customer's core network.
Which step should the engineer take before the segment routing is enabled and is running with BGP?
- A. Segment routing must be configured with EIGRP.
- B. MPLS must be configured.
- C. Explicit-null must be configured for all neighbors.
- D. Segment routing must be configured with ISIS.
Answer: B
NEW QUESTION # 99
Refer to the exhibit.
When implementing SRv6, which SID does R2 propagate into area 0 for the prefix 2001:DB8:1:1/128?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 100
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION # 101
Refer to the exhibit.
Refer to the exhibit. After a recent network implementation project, customer A is performing stress testing to verify network redundancy at the branch office connected to R4. When the link from R2 is shut Oown as shown, the SLA tracking object fails and the cost of the link between R2 and R4 increases to 100. However, a traceroute operation from a PC in the Branch office shows that traffic to HQ is still routed via R2. Which solution corrects the problem and optimizes traffic flow via R3 without creating operational overhead?
- A. Use multiarea adjacency to extend Area 10 to the link between R2 and R3.
- B. Configure two OSPF processes on R2 and R3 and redistribute traffic between them.
- C. Redistribute routes from BGP to OSPF as type El.
- D. Create a virtual channel from R3 to R4.
Answer: C
NEW QUESTION # 102
Refer to the exhibit.
Router 1 is a core ABR in a Cisco Unified MPLS environment. All of the router 1 BGP peers are established, but traffic between customers is failing. Which BGP configuration must be added to the configuration?
- A. It must be configured with send labels
- B. It must be configured for graceful restart
- C. It must be configured with PIC edge
- D. It must be configured with a route reflector
Answer: A
NEW QUESTION # 103
Refer to the exhibit.
CE1 and CE2 cannot communicate through the service provider BGP peering is established between PE1 and PE2. IS-IS is the only routing protocol running in the service provider core. What step can be done to troubleshoot the issue?
- A. Confirm that IS-IS is running with metric-style narrow.
- B. Verify the MPLS LSPs.
- C. Switch the IGPs running in the core from IS-IS to OSPF to support a Cisco MPLS TE tunnel from PE1 to PE2.
- D. Configure BGP between CE and PE routers.
Answer: A
NEW QUESTION # 104
Drag and drop the features about multicast from the left onto the multicast protocols on the right. Not all options ate used.
Answer:
Explanation:
NEW QUESTION # 105
Refer to the exhibit.
An administrator is troubleshooting Internet access issues on a customer's network. After applying this ISIS configuration to R1, the administrator notices that it fails to redistribute the default route into IS-IS. After checking the connectivity between the ISIS router and the ISP router the engineer confirmed there is Layer 3 connectivity between them Which action should be taken to correct the problem?
- A. Configure the default route under any routing protocol other than IS-IS
- B. Associate the default route with a VRF
- C. Configure R1 as a Layer 1 router
- D. Add the default-information originate command to the configuration
Answer: D
NEW QUESTION # 106
Refer to the exhibit
Router R1 is configured to advertise outgoing SA messages to routers R2 and R3, but to receive incoming SA messages only from R2. Which additional configuration must an engineer apply to router R1 so it filters all MSDP SA messages from Domain-C?
- A. R3# ip msdp password peer 192.168.1.1
- B. R3# ip msdp sa-filter out 192.168.3.1
- C. R1# ip msdp sa-filter in 192.168.3.1
- D. R1# ip msdp password peer 192.168.3.1
Answer: C
NEW QUESTION # 107
Refer to the exhibit.
Answer:
Explanation:
Solution :-
R1
Router bgp 100
Neigh 10.3.3.3 remote-as 100
Neigh 10.3.3.3 update-source loopback0
Address-family ipv4
Neigh 10.3.3.3 next-hop-self
Aggregate-address 172.16.100.0 255.255.252.0 summary-only
Copy run start
R3
Router bgp 100
Neigh 10.1.1.1 remote-as 100
Neigh 10.1.1.1 update-source loopback 0
Copy run start
Verification:-
NEW QUESTION # 108
Which two differences should be considered when deciding whether to implement to implement routing policies or route maps? (Choose two.)
- A. Route maps require an explicit deny at the end of the sequence, but routing policies have an implicit deny at the end of the program.
- B. Route maps are supported in Cisco 10S Software and routing policies are supported in Cisco IOS XR Software.
- C. Sequences are added after implementing a route map, but routing policies must be reconfigured when change is needed.
- D. Route maps are implemented using hierarchical policies, but routing policies must be implemented sequentially.
- E. Route policies require sequence numbers, but route maps are implemented without sequencing.
Answer: B,C
NEW QUESTION # 109
Drag and Drop Question
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network.
Which tasks should the engineer use to solve the routing issues?
Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)
Answer:
Explanation:
NEW QUESTION # 110
A network engineer is troubleshooting OSPF multiare A.
Which Cisco IOS XR feature should the engineer use in order to streamline OSPF issue?
- A. show ip ospf topology command
- B. DR support for topology management
- C. hierarchical CLI
- D. routing process enabled by default on all interfaces
Answer: C
Explanation:
OSPF Hierarchical CLI and CLI Inheritance
Hierarchical CLI is the grouping of related network component information at defined hierarchical levels such as at the router, area, and interface levels. Hierarchical CLI allows for easier configuration, maintenance, and troubleshooting of OSPF configurations. When configuration commands are displayed together in their hierarchical context, visual inspections are simplified. Hierarchical CLI is intrinsic for CLI inheritance to be supported.
With CLI inheritance support, you need not explicitly configure a parameter for an area or interface. In the software, the parameters of interfaces in the same area can be exclusively configured with a single command, or parameter values can be inherited from a higher hierarchical level-such as from the area configuration level or the router ospf configuration levels.
More information: https://www.cisco.com/c/en/us/td/docs/iosxr/ncs5500/routing/71x/b-routing-cg-ncs5500-71x/b-routing-cg-ncs5500-71x_chapter_011.html#con_1059437 Reference:
guide/rc40xr12k_chapter4.html#con_1059437
NEW QUESTION # 111
Refer to the exhibit.
Router 1 is connected to router 2 on interface TenGigE0/1. Which interface provides the alternate path to 172.16.200.9/32 when the link between router 1 and router 2 goes down?
- A. A backup path must be statically installed
- B. TenGigE0/2 interface provides the alternate path
- C. A primary path must be manually installed
- D. TenGigE0/1 interface provides the alternate path
Answer: B
NEW QUESTION # 112
Compare different features between OSPFv2 and OSPFv3. Drag and drop the descriptions of OSPF from the left onto the correct OSPF versions on the right.
Answer:
Explanation:
NEW QUESTION # 113
What is the role of segment routing mapping server?
- A. It reads and translates remotely received SIDs from other mapping servers to create SID mapping entries.
- B. It selects multiple mapping entries to create overlapping active mapping policies.
- C. It advertises a local SID mapping policy to all the mapping clients.
- D. It works with IGP instances to calculate the prefix-SIDs in the absence of a mapping policy.
Answer: C
Explanation:
NEW QUESTION # 114
Refer to the exhibit.
Traffic flow from router R1 to router R6 is delay-sensitive It must consider potential link-failure and node-failure conditions Which configuration must an engineer apply to router R1 to route traffic to router R6 if router R2 fails?
- A. Option C
- B. Option D
- C. Option A
- D. Option B
Answer: D
NEW QUESTION # 115
After an engineer configures BGP in R1, it starts receiving this message
*Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1
2/6 (unacceptable hold time) 0 bytes
Which action makes the peering come back up again?
- A. Set up a hello timer higher.
- B. Set up a minimum hold-down timer higher.
- C. Set up a hold-down timer higher.
- D. Make a soft reset to the peer.
Answer: B
NEW QUESTION # 116
Refer to the exhibit. Traffic flow from router R1 to router R6 is delay-sensitive. It must consider potential link-failure and node-failure conditions.
Which configuration must an engineer apply to router R1 to route traffic to router R6 if router R2 fails?
- A. Option C
- B. Option D
- C. Option A
- D. Option B
Answer: D
NEW QUESTION # 117
......
300-510 [Sep-2023] Newly Released] Exam Questions For You To Pass: https://www.actualvce.com/Cisco/300-510-valid-vce-dumps.html
300-510 Answers 300-510 Free Demo Are Based On The Real Exam: https://drive.google.com/open?id=1R2bmFRdHsK2HNWRa7WTM1l_0T4CaDQMf