Most UptoDate Cisco 300-625 Exam Dumps PDF 2021 [Q14-Q36]

Most UptoDate Cisco 300-625 Exam Dumps PDF 2021

100% Free CCNP Data Center 300-625 Dumps PDF Demo Cert Guide Cover

Exam Content to Explore

Each candidate has 90 minutes to write the Cisco 300-625 exam, which is only available in English and includes multiple-choice questions. There will be 60 items in total and you will need to earn at least 825 points to clear the test with flying colors. If you are ready to continue on the path of the Cisco certification, you can refer to the Pearson VUE website to schedule the exam date.

NEW QUESTION 14
Which feature on MDS platforms ensures that the code that is running on the hardware platform is authentic and unmodified, while also validating the BIOS to eliminate any rootkits.

A. Secure Unique Device Identifier
B. BIOS Secure Boot
C. UEFI Secure Boot
D. Cisco Secure Boot

Answer: D

Explanation:
Section: Deployment

NEW QUESTION 15
A storage network engineer is implementing SAN telemetry for a SAN infrastructure using Cisco DCNM for SAN. Which command is used to check the session status for telemetry operation?

A. show telemetry transport
B. show telemetry pipeline stats
C. show analytics system-load
D. show telemetry control stats

Answer: A

Explanation:
Section: Management and Monitoring

NEW QUESTION 16
Refer to the exhibit. A network engineer created a new user that uses the VSAN-Admin role on a Cisco MDS switch so a new colleague can manage the VSANs configured on the switch.
Which action is required for the configuration to give permission to the new colleague?

A. permit vsan 1-1000 must be configured as rule 5.
B. permit vsan 1-1000 must be configured as rule 1.
C. permit vsan 1-1000 must be configured under the VSAN policy deny.
D. permit vsan 1-1000 must be configured under the VSAN policy allow.

Answer: C

NEW QUESTION 17
A network engineer is configuring a Cisco MDS switch for FCoE. Which two conditions must be considered during the implementation phase? (Choose two.)

A. FCoE is already enabled on a Cisco MDS switch.
B. VLAN 1 or the native VLAN can be mapped to an FCoE VSAN.
C. On the Cisco MDS, the MTU is set equal to 2112.
D. The QoS policy must be identical to other Cisco FCoE switches in the network.
E. On Cisco MDS switches, system-defined class maps for class-FCoE and class-default are enabled but can be deleted.

Answer: D,E

NEW QUESTION 18
Refer to the exhibits. A storage network engineer activates a zoneset on MDS-A and verifies the successful activation (Exhibit 1). The engineer is then notified that there is a SAN outage (Exhibit
2). What is the cause of the outage?

A. Another network engineer activated the zoneset ZoneSetMDS-B-VSAN100 command on another switch in the fabric.
B. Another network engineer activated zoneset ZoneSetMDS-B-VSAN100 on MDS-A.
C. Another network engineer issued the zone default-zone permit vsan 100 command on another switch in the fabric.
D. Another network engineer issued the zone mode enhanced vsan 100 command on another switch in the fabric.

Answer: C

NEW QUESTION 19
Which item is a component of Cisco DCNM?

A. Cisco DCNM for Cisco UCS Manager
B. Cisco DCNM FabricPath license
C. Cisco DCNM for SAN and Cisco DCNM for LAN
D. Cisco DCNM for B- and C-Series servers

Answer: C

NEW QUESTION 20
Which two platforms support the FCoE protocol? (Choose two)

A. Cisco Nexus 7010 Series
B. Cisco MDS 9222i Series
C. Cisco MDS 9148S Series
D. Cisco Nexus 2332TQ Series
E. Cisco Nexus 2248TP Series

Answer: A,D

NEW QUESTION 21
Refer to the exhibit.

Refer to the exhibit. The san-user must configure FSPF on the VSAN 500. but fails. An operator with network administrative rights must authorize the san-user to perform this work. Which configuration must the operator apply?

A. MDS-A(config)# role name sangroup
MDS-A(config-role># no rule 2
B. MDS-A(config)# role name sangroup
MDS-A(config-role)# rule 2 permit config feature vsan
C. MDS-A(config)# role name sangroup
MDS-A(config-role)# vsan policy deny
MDS-A(config-role-vsan)# permit vsan 500
D. MDS-A(config)# role name sangroup
MDS-A(config-role)# rule 4 permit config feature fspf

Answer: B

NEW QUESTION 22
The principal switch on a Fibre Channel network fails to assign requested domain to a subordinate switch.
What are two reasons? (Choose two.)

A. The requested domain is outside the allowed list.
B. The fabric is locked.
C. The persistent FC ID feature is not enabled.
D. Cisco Fabric Services distribution is not enabled on the switch.
E. An existing switch already has the requested domain assigned.

Answer: A,E

NEW QUESTION 23
Refer to the exhibit. What is the result of merging the fabric?

A. The merged fabric has NAT enabled.
B. The merge is invalid.
C. The merged fabric contains only service group Group1.
D. The merged fabric IVR VSAN topology is set to activate.

Answer: C

NEW QUESTION 24
What is the function of the 0xFFFFFC address in a Fibre Channel fabric?

A. fabric controller
B. name server
C. time server
D. management server

Answer: A

NEW QUESTION 25
Refer to the exhibit.

A network engineer must configure the SAN telemetry streaming feature to stream statistics form a Cisco MDS
9000 Series Switch to two external receivers with the IP addresses 192.168.1.4 and 192.168.1.5. Which two configurations accomplish this configuration? (Choose two.)

A. Add dst-grp 300 under subscription 200.
B. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 300.
C. Add dst-grp 100 under subscription 200.
D. Add dst-grp 200 under subscription 100.
E. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 100.

Answer: D,E

Explanation:
Section: Management and Monitoring

NEW QUESTION 26
Which tool was used to manage Cisco Storage networking before Cisco DCNM?

A. Cisco Adaptive Security Device Manager
B. Cisco Fabric Manager
C. Cisco UCS Director
D. Cisco UCS Manager

Answer: B

NEW QUESTION 27
After user account attributes are modified in Cisco NX-OS, when do changes to the user's session attributes take effect?

A. when the user logs out of a session
B. immediately
C. when the user creates a new session
D. at the scheduled time

Answer: C

NEW QUESTION 28
Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?

A. MDS(config)# interface fc 1/1
MDS(config-if)# fcsp esp manual
MDS(config-if-esp)# mode gem
B. MDS(config)# interface fc 1/1
MDS(config-if)# fcsp mode gem
MDS(config-if-fcsp)# fcsp esp manual
C. MDS(config)# fcsp esp manual
D. MDS(config)# interface fc 1/1
MDS(config-if)# fcsp esp manual

Answer: A

NEW QUESTION 29
Which Cisco NX-OS command displays the VSAN that is associated with each FCID?

A. show fcdomain
B. show vsan database
C. show flogi database
D. show fc2 plogi

Answer: A

Explanation:
Section: Deployment

NEW QUESTION 30
Refer to the exhibit.

A network engineer must configure the SAN telemetry streaming feature to stream statistics form a Cisco MDS 9000 Series Switch to two external receivers with the IP addresses 192.168.1.4 and 192.168.1.5. Which two configurations accomplish this configuration? (Choose two.)

A. Add dst-grp 300 under subscription 200.
B. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 300.
C. Add dst-grp 100 under subscription 200.
D. Add dst-grp 200 under subscription 100.
E. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 100.

Answer: D,E

NEW QUESTION 31
A storage network engineer must configure a 48-port Cisco MDS switch to reject any login requests to VSAN 10 from unauthorized Fibre Channel devices and switches. All the devices that were already logged in to the switch from this VSAN must be allowed without any manual configuration. Which configuration must be applied?

A. switch(config)# feature port-security
switch(config)# port-security database vsan 10
switch(config-port-security)# any-wwn interface fc1/1 - fc1/48
B. switch(config)# feature port-security
switch(config)# port-security activate vsan 10 no auto-learn
C. switch(config)# port-security activate vsan 10
D. switch(config)# feature port-security
switch(config)# port-security activate vsan 10

Answer: C

NEW QUESTION 32
Refer to the exhibit. A network engineer must configure the SAN telemetry streaming feature to stream statistics form a Cisco MDS 9000 Series Switch to two external receivers with the IP addresses 192.168.1.4 and 192.168.1.5.
Which two configurations accomplish this configuration? (Choose two.)

A. Add dst-grp 300 under subscription 200.
B. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group
100.
C. Add dst-grp 100 under subscription 200.
D. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group
300.
E. Add dst-grp 200 under subscription 100.

Answer: B,E

NEW QUESTION 33
Refer to the exhibit. A port channel has been configured between a Cisco MDS and a Cisco Fabric Interconnect switch. Which interface(s) in the port channel carry the control plane traffic?