New 2024 Realistic Free EMC D-UN-DY-23 Exam Dump Questions and Answer
D-UN-DY-23 Practice Test Engine: Try These 469 Exam Questions
EMC D-UN-DY-23 (Dell Unity Deploy 2023) Exam is a certification exam that validates the skills and knowledge required to deploy and manage Dell Unity storage systems. D-UN-DY-23 exam covers a range of topics including installation, configuration, management, and troubleshooting. Passing D-UN-DY-23 exam demonstrates that an IT professional has the expertise required to deploy and manage Dell Unity storage systems effectively.
To be eligible to take the EMC D-UN-DY-23 exam, you must have a good understanding of storage systems, networking, and server technologies. You should also have experience with Dell EMC Unity storage systems and be familiar with the command line interface (CLI) and graphical user interface (GUI) used to manage these systems.
NEW QUESTION # 17
A system administrator receives a warning that their DPE I/O Module has a fault.
In this situation, which type of replacement is required?
- A. Non-Hot-pluggable FRU
- B. Hot-pluggable CRU
- C. Hot-pluggable FRU
- D. Non-Hot-pluggable CRU
Answer: D
NEW QUESTION # 18
What are two characteristics of Data Reduction? (Select 2)
- A. Available on the Dell UnityVSA
- B. Configured through Unisphere
- C. Can be used on LUNs in replication sessions
- D. Supported on All-Flash pools only
- E. Can be enabled only on block storage resources
Answer: B,D
NEW QUESTION # 19
What should be done prior to a Unity software upgrade to ensure that no underlying problems exist that may prevent a successful upgrade?
- A. Check for ETAs
- B. Enable Service mode
- C. Perform a Health Check
- D. Check for FCOs
Answer: C
NEW QUESTION # 20
Which quota policy calculates disk usage in 8 KB units?
- A. User
- B. Directory Tree
- C. File Size
- D. Block
Answer: D
NEW QUESTION # 21
A system administrator deployed a UnityVSA to their vSphere environment. They did not add the management IP to the UnityVSA during the installation.
Which command must be used to apply the management IP from the vSphere UnityVSA console?
- A. svc_inject
- B. svc_initial_config
- C. svc_change_hw_config
- D. svc_ipmi
Answer: B
Explanation:
Explanation
To apply the management IP from the vSphere UnityVSA console, the system administrator must use the svc_initial_config command. This command allows the user to configure the initial network settings for the UnityVSA, such as the management IP address, subnet mask, gateway, and DNS servers. The svc_ipmi command is used to configure the IPMI settings for the UnityVSA, such as the IPMI IP address, username, and password. The svc_change_hw_config command is used to change the hardware configuration of the UnityVSA, such as the number of CPU cores, memory size, and disk size. The svc_inject command is used to inject faults into the UnityVSA for testing purposes.
References: [Dell EMC UnityVSA Installation Guide], [Dell EMC UnityVSA Command Line Interface Reference Guide]
NEW QUESTION # 22
What are CNA port identifiers on Dell Unity XT 380/380F?
- A. 2 and 3
- B. 4 and 5
- C. 0 and 1
Answer: A
NEW QUESTION # 23
What happens when the user performs the Compress Now operation?
- A. Data is immediately compressed at its current location
- B. LUN is copied to a user-selected pool and the data is compressed
- C. Data is compressed by creating a move session to a LUN within the same pool
- D. Data is compressed by creating a move session to the LUN within a user-selected pool
Answer: C
NEW QUESTION # 24
A system administrator has asynchronous remote replication configured between a pair of systems and replications currently operating normally.
When the administrator views a replication session on the Unisphere Session page for session the destination system, which option is available when viewing "More Actions"?
- A. Pause
- B. Failover with sync
- C. Sync
- D. Failover
Answer: B
NEW QUESTION # 25
Which feature provides the ability to provision block and file storage for Microsoft Windows or Microsoft SharePoint sites?
- A. EMC Virtual Storage Integrator
- B. EMC Storage Integrator for Windows
- C. vStorage APIs for Array Integration
- D. Array Offloaded Data Transfer
Answer: B
NEW QUESTION # 26
What is the default setting of Advanced Deduplication when Data Reduction is selected within Unisphere?
- A. Enabled for both thick and thin LUNs
- B. Disabled for thick LUNs and enabled for thin LUNs
- C. Enabled for thin LUNs in an All-Flash pool
- D. Disabled for thin LUNs in an All-Flash pool
Answer: C
NEW QUESTION # 27
On which platform(s) is FAST Cache available?
- A. Unity hybrid systems only
- B. All Flash Unity systems only
- C. Physical and UnityVSA systems
- D. Physical Unity systems only
Answer: A
NEW QUESTION # 28
Which Unity system configuration can be performed using the Unisphere Initial Configuration wizard?
- A. Configure Link Aggregation
- B. Register host HBA WWNs
- C. Register host iSCSI initiators
- D. Add iSCSI network interfaces
Answer: D
NEW QUESTION # 29
What is a characteristic of Automatic UFS64 File System extension?
- A. Allocated space remains unchanged after extend operation
- B. File system cannot auto-extend past the provisioned size
- C. Auto-extension can exceed the file system visible size
- D. Array I/O service to clients is disrupted during auto-extension
Answer: B
NEW QUESTION # 30
On which systems is Quality of Service available?
- A. UnityVSA systems only
- B. Physical Unity and UnityVSA systems
- C. All Flash Unity systems only
- D. Physical Unity systems only
Answer: B
NEW QUESTION # 31
What are four constraints defined in a VMware Capability Profile?
- A. Service Level, Access, Protocol, and Space Efficiency
- B. Service Level, Drive Type, RAID Level, and Space Efficiency
- C. Protocol Endpoint, Drive Type, RAID Level, and VM UUID
- D. Capacity, Drive Type, RAID Level, and Data Reduction
Answer: B
NEW QUESTION # 32
A storage administrator has configured an SMB share with the Pool Automatic Deletion retention policy.
With default settings applied, what will happen when the pool crosses 95%?
- A. The Dell EMC Unity system will only delete the oldest snapshot of the configured schedule
- B. The Dell EMC Unity system will delete snapshots until 85%, pool space is reached
- C. Nothing. The default setting is that no snapshots will be deleted automatically
- D. Nothing. When the snapshot reaches 25% of the pool size, snapshots will be deleted until 20% of the pool size is reached
Answer: B
NEW QUESTION # 33
Where can Unity Compression be enabled?
- A. All-Flash and 3-tier pools
- B. Thick LUNs only
- C. AI-Flash systems only
- D. All-FIash pools only
Answer: B
NEW QUESTION # 34
For high availability within iSCSI, connections should be attached using what?
- A. Flow control
- B. Twinax cables
- C. Jumbo frames
- D. Different subnets
Answer: D
NEW QUESTION # 35
An administrator initially created a Thin Provisioned file system on Dell EMC Unity. They now want to change that file system (FS) to Thick Provisioned.
What is a consideration?
- A. The FS cannot be changed from Thin to Thick
- B. Unmap/Unmount the FS and change FS properties
- C. Unmap/unmount the FS and use the Initial Configuration Wizard
- D. Convert the FS from Thin to Thick through Unisphere
Answer: A
NEW QUESTION # 36
Which Dell EMC Unity storage resource allows modification of its block size during creation?
- A. VVol block datastore
- B. Block datastore
- C. VVol file datastore
- D. NFS datastore
Answer: D
NEW QUESTION # 37
What is a benefit of Dell Unity XT dynamic pools?
- A. Improved access to data residing on the drive tiers
- B. Reduced time to rebuild a failed drive
- C. Protects written data from modification
- D. Enables throughput and bandwidth throttling
Answer: B
NEW QUESTION # 38
What is required for file system creation on Unity?
- A. DNS configuration
- B. NTP configuration
- C. Shares
- D. NAS Server
Answer: D
NEW QUESTION # 39
What is the correct sequence of steps to create a replication session on an existing LUN?
- A. Select the Replication tab from the LUN Properties page.
Start the Configure Replication wizard.
Choose the destination.
Choose the replication mode. - B. Start the Configure Replication wizard.
Choose the destination.
Choose the replication mode.
Select the Replication tab from the LUN Properties page. - C. Start the Configure Replication wizard.
Choose the replication mode.
Select the Replication tab from the LUN Properties page.
Choose the destination. - D. Choose the destination.
Start the Configure Replication wizard.
Select the Replication tab from the LUN Properties page.
Choose the replication mode.
Answer: A
NEW QUESTION # 40
A storage administrator has a Unity system with its integrated CNA ports having 10 Gb/s optical SFPs. The system is also configured with two IO modules: a 2-port 10 GbE optical IO module in expansion slot 0, and a 4-port 16 Gb/s FC optical IO module in expansion slot 1.
Which Unity port can be used for synchronous replication?
- A. Only port 0 of the slot 1 IO module
- B. Any optical port
- C. Any port in the slot 0 IO module
- D. Only integrated port 4
Answer: A
NEW QUESTION # 41
......
Earning the EMC D-UN-DY-23 certification demonstrates your expertise in Dell Unity storage system deployment and management. Dell Unity Deploy 2023 Exam certification is highly valued by IT organizations that use Dell Unity storage systems and can help you advance your career as a storage administrator or IT professional.
Guaranteed Success in Proven Professional D-UN-DY-23 Exam Dumps: https://www.actualvce.com/EMC/D-UN-DY-23-valid-vce-dumps.html
EMC D-UN-DY-23 Daily Practice Exam New 2024 Updated 469 Questions: https://drive.google.com/open?id=1r3-Nh7vlJFKQVoINMaO-NN3__AZq9q_A