Pass Your Exam Easily! PD1-001 Real Question Answers Updated on Nov 25, 2022
Actual Questions Answers Pass With Real PD1-001 Exam Dumps
NEW QUESTION 71
Which of the following describes the function of lamps located inside the fuser?
- A. Charges the pressure roller
- B. Removes excess toner
- C. Generates heat
- D. Removes residual charges
Answer: C
NEW QUESTION 72
The purpose of a charge coupled device (CCD) array is to convert:
- A. light to an analog voltage.
- B. light to a digital voltage.
- C. an analog voltage from an 8-bit digital signal.
- D. a digital signal to an analog voltage.
Answer: A
NEW QUESTION 73
When combining all colors 100% in the subtractive color model, which of the following is the closest resulting color?
- A. Black
- B. Red
- C. Cyan
- D. Blue
Answer: A
NEW QUESTION 74
The print head moves left to right, drops down a line, then right to left. Which of the following represents this method of printing?
- A. Unidirectional
- B. Dithering
- C. Duplexing
- D. Bi-directional
Answer: D
NEW QUESTION 75
Which of the following is the main function of the developer unit metering blade?
- A. To prevent the toner from escaping from the developer unit.
- B. To provide an even layer of developer.
- C. To remove dust and debris from the toner.
- D. To ensure toner and developer are evenly mixed.
Answer: B
NEW QUESTION 76
Which of the following is a technique used for isolating problems?
- A. Change paper feed tires first
- B. Complete a full maintenance
- C. Eliminate non-causes from the scenario
- D. Replace the consumables
Answer: C
NEW QUESTION 77
Which of the following steps should a technician perform FIRST on arrival at a customers premises?
- A. Make sample test copies.
- B. Remove power plug from machine.
- C. Make appropriate introduction.
- D. Ask open ended questions about the customers issue.
Answer: C
NEW QUESTION 78
A customer brought an ink dispersion printer into the service facility. The unit wil not print in black but prints in color with no issues. The technician decided to replace the print head, carriage assembly, and logic PCB all at the same time. The device is still having the same problem. The technician should have followed which of the following troubleshooting methodologies?
- A. Observe, establish theory, test / analyze, implement, validate
- B. Observe, test/ analyze, establish theory, validate, implement
- C. Test / analyze, observe, validate, establish theory, implement
- D. Observe, validate, test / analyze, establish theory, implement
Answer: A
NEW QUESTION 79
Which of the following components uses heat and pressure?
- A. Transfer Roller
- B. Charge Roller
- C. Fuser
- D. Developer
Answer: C
NEW QUESTION 80
Which of the following components has failed if toner can be rubbed off the media?
- A. Fuser unit
- B. Developer unit
- C. Photoconductor
- D. Charge roll
Answer: A
NEW QUESTION 81
When scanning a document through an ADF the customer notices a thin black line from the lead edge to trail edge of the original. Which of the following is a possible cause of the problem?
- A. Corrupt PCL driver
- B. Weak power supply
- C. Worn feed roller
- D. Contaminated CIS
Answer: D
NEW QUESTION 82
When replacing a printed circuit board (PCB), always:
- A. observe ESD procedures.
- B. place the PCB on a metal surface.
- C. clean the PCB surface with a vacuum cleaner.
- D. wear gloves and safety glasses of a suitable material.
Answer: A
NEW QUESTION 83
The purpose of the separator roller is to prevent:
- A. paper dust contamination.
- B. excess roller wear.
- C. multi-sheet feeding.
- D. print quality issues.
Answer: C
NEW QUESTION 84
A magnetic switch is a switch that:
- A. uses a magnet to hold the switch in place.
- B. uses a magnet to actuate the switch.
- C. uses a magnetic field to move diverters.
- D. is used to check for magnetic particles on the printed page.
Answer: B
NEW QUESTION 85
When troubleshooting a void print area issue, which of the following is the BEST step for isolating the issue in a MFD?
- A. Stopping the output at the exit rollers
- B. Stopping the output under the photoconductor
- C. Stopping the output at the registration roller
- D. Stopping the output in the fuser
Answer: B
NEW QUESTION 86
......
New PD1-001 Dumps - Real CompTIA Exam Questions: https://www.actualvce.com/CompTIA/PD1-001-valid-vce-dumps.html